Dryer hookup 3 prong to 4, the best, safest, and cheapest solution is to install a new cord
How Does One Convert a 4 Prong Dryer Cord to Fit a 3 Prong Outlet? | michelemcleodbarrelhorses.com
Tape the wire with a label with "B," "W," and "R" written on it. Be sure to remove the bonding strip.
A range cord made for a cooking range looks very similar and also has 4 prongs in about the same locations. Things You Will Need. Remove the old dryer cord and set it aside.
Video of the Day
Remove the cover plate from the wire terminal block, exposing the wires inside. The green wire will attach to the spot where the strap was removed from the frame of the dryer see above. Installing the 4 Prong Cord and Plug The white wire is placed on the center terminal, where it belongs.
There will be a metal strap or wire fastened to the place where the white wire was, attaching to the frame of the dryer. Remove the nut, place the threaded portion through the wall of the dryer, and replace the nut.
Without it, if there is an electrical problem later, the frame may become energized and present a huge shock hazard. Pull the old cable out through the connector and save it in case you ever move into a home with a 3 hole socket. You can use a 10 wire instead of a strap.
A removable, metal plate covers a larger opening where the cord enters the housing.
The outer two screws should be yellowish brass. Typical V outlets as a dryer is use black and red as the "hot" wires, but any colors except white and green are legally acceptable. Notice the clamp holding the wire to the dryer.
Note the metal piece that goes from the white wire to the frame of the dryer. In place of that wire a ground strap or short piece of 10 wire preferably green must be installed.
The cord should enter the dryer through some kind of connector to prevent strain on the screws where the wire terminates. Push the new cable through the connector.
How to Wire a Three-Prong Outlet to a Four-Prong Outlet | eHow
Turn the breaker back on. Remove this strap or wire, and once more, save it for possible use in years to come. The four-pronged cord has been loosened from the dryer wall and is ready to be disconnected from the terminals. With the cable through the connector, it is time to terminate attach the wires to the screws where the old wires came out.
Disconnect the bonding strap, which will be either a metallic strip or green wire connected to the middle white wire terminal, which is neutral, to the green screw above the white wire.
Dryer hook up 4 prong to 3 prong - michelemcleodbarrelhorses.com Community Forums
Locate the access panel on the back of the dryer. While the red and black wires are interchangeable, the white wire is not; make sure it goes to the center terminal, where the old white wire was. Most three-wire cords do not have colored wires, so instead of matching colors, identify the wires using the relative position of the wires in the cord.
The difference is that a dryer cord has two straight prongs and two bent ones, while a range cord has three straight prongs and one bent one. Any and all other colors are open for use, except that they cannot be used as either a neutral or ground.
Remove each wire from the screw or stud holding it, making sure to save all nuts or screws. Unscrew the access panel, which will normally be two or four screws holding it on and located near where the cord comes out of the dryer.
The ground strap has been removed and the green wire attached to where it mounted on the frame of the dryer.
If the old wires are colored, note where the white wire ends. Four-prong dryer cords have four wires including the neutral and two hots plus a green ground wire.
How to Change a 4-Prong Dryer Cord and Plug to a 3-Prong
The center screw, which is for the neutral wire, should be silver. It is a wise precaution to turn off the breaker before plugging the dryer in, just in case something is wired wrong. Many dryers are placed very close to the wall where the exhaust vent is located, requiring that the hose be badly kinked in order to hook up to it, and rigid metal elbows are available to help alleviate this problem.
Turn each of the screws counterclockwise using a small adjustable wrench or screwdriver. There is high voltage inside volts that can give you a very nasty shock, even kill you. So, make sure to find and follow the directions for your dryer when installing a new cord!
Make sure there is no chance of this, by unplugging the dryer before proceeding any further. You should see three wires, red, white, and black.
My New Home Needs a Dryer Plug Adapter
Unplug the power to the dryer. This assumption may be wrong. It does not go on the terminal board where the white wire is, but to the frame.
It is wise to turn the power off at this point, just in case something has been wired wrong. Do not ignore this step! What the three-wire connection will look like, including a metal ground strap circled between the dryer frame and the white wire.
Congratulations on doing your own home repair job!
- Unam vs tigres online dating
- Is asap rocky dating
- Ketamina liquidia online dating
- Selena gomez and gregg sulkin dating
- Banerjee duflo dating
- Best dog kennels in bangalore dating
- Thor el martillo de los dioses online dating
- Opus 420 dating
- Pre-dating new orleans
- Hook up wireless keyboard to ps3
- Seoulistic dating simulator
- Age difference dating chart video